TFM-04 Fire Extinguisher License – A (FEL-A) Practice Test

These questions are part of the practice quiz. Start practicing

• Which scenario would require disposal or replacement rather than recharge?
• Can you use CO2 for hazards that contain oxygen?
• If a hose fails the pressure test, what should be done?
• Which NFPA standard covers the installation of Foam-Water Sprinkler and Foam-Water Spray Systems?
• How often shall CO2 systems be inspected/tested?
• What information is typically conveyed on an extinguisher label regarding its capabilities?
• What action is required if the hose test reveals leaks (failure)?
• Which standard covers Halon 1301 Fire Extinguishing Systems?
• Which NFPA standard governs the inspection, testing, and maintenance of water-based fire protection systems?
• How does an extinguisher fit into a broader fire safety program?
• Mechanical grooved couplings and fittings are permitted on which type of system?
• Which of the following locations is not a listed warning-sign placement requirement for CO2 systems?
• What hazards can occur when operating extinguishers in enclosed spaces?
• Which statement is true regarding the use of galvanized pipe for foam concentrate piping?
• In high-pressure CO2 piping, the required fitting class is which?
• Which standard covers Clean Agent Fire Extinguishing Systems?
• To keep an extinguisher ready in a high-traffic area, you should:
• Which statement is correct about hose testing frequencies?
• Which statement describes when mandatory annual maintenance by a qualified technician is required?
• Which elements should a post-incident report include after extinguisher use?
• How often shall foam systems be inspected?
• Is galvanized pipe permitted for foam concentrate piping?
• Can you perform a visual inspection on a halon 1301 system in lieu of a hydrostatic test?
• Which extinguisher media is typically used for Class K (kitchen oils) fires?
• Safety signs should conform to which standard?
• ASTM A53 butt weld is permitted on which type of system?
• How often shall you inspect halon 1301 enclosure?
• How often should the foam concentrate pump operation be checked?
• Which statement correctly describes a underground pipe surveillance interval?
• Foam concentrate fittings shall NOT be made of which material?
• FDC size?
• Who typically performs CO2 operational condition checks?
• The halon 1301 visual inspection in lieu of hydro test is permissible only if the system has remained in service and the inspection is performed every 5 years. True or False?
• Which option lists all basic types of foam systems?
• What actions should you take if extinguisher residue contaminates a workspace after use?
• The B rating on an extinguisher indicates effectiveness against which type of fire?
• If a gauge reading is outside the 3% tolerance, what action should be taken?
• FFFP stands for?
• Inert gases are made up of?
• After pressure testing hoses, what is the maximum drying temperature?
• The oil content limit in the system is measured in which unit?
• During the hose pressure test, which steps are required?
• What steps should you take if an extinguisher discharges or is damaged during use?
• Low pressure system hoses shall be tested at what PSI?
• Which component requires a 30-day check of its operation in the foam concentrate system?
• If a hose fails the pressure test, what action is required?
• Who should inspect or test CO2 systems?
• What information does extinguisher labeling typically provide?
• Can you use cast iron, ASTM A120 steel, or non-metallic pipe on a Halon 1301 system?
• Halocarbons are?
• Inert gas must discharge 95% within how many seconds for class B fires?
• Which statement is true?
• Which media is suitable for Class A and B fires?
• Lube/joint compound/tape can not be applied to which threads?
• Maintenance should be performed by a qualified technician at intervals per code or manufacturer.
• Which topics should be included as core FEL-A training?
• Which fire classes correspond to ordinary combustibles, flammable liquids, and electrical equipment?
• What percentage net weight loss on a Halon 1301 system requires refill or replacement?
• What is the correct procedure for pressure testing all system hoses?
• What percentage loss on a CO2 system requires replacement?
• Oil content shall not exceed how many parts per million?
• What percentage pressure loss on a Halon 1301 system requires replacement or refill?
• Flange joints shall be what class?
• A CO2 cylinder stored at ambient room temperature is classified as which type of system?
• What information does the extinguisher inspection tag provide?
• Which statement about foam concentrate piping material is true?
• Which NFPA standard addresses inspection/maintenance for NFPA 15 systems?
• AFFF stands for?
• Class K extinguishers are designed for which scenario?
• What is hydrostatic testing and why is it essential for extinguisher safety?
• Which item is not typically required when transporting extinguishers?
• A CO2 cylinder stored at 0°F and 300 psi would be classified as which type of system?
• What does an ABC rating indicate on an extinguisher?
• AHJ stands for which term?
• What safety precautions are important when using an extinguisher near electrical equipment?
• Hydrostatic testing on extinguishers is typically performed at what intervals and what does it verify?
• DOT containers must be tested at least every how many years before recharging?
• Why is it important to keep extinguishers unobstructed and accessible?
• Foam concentrate shall be sent annually to test what?
• How often shall you inspect CO2 operational condition?
• During a multi-extinguisher incident, what safety consideration regarding exits is important?
• Which statement correctly contrasts passive and active protection in extinguisher readiness?
• Maximum difference between tested gauge and calibrated gauge?
• High-pressure CO2 fittings shall be what class?
• Which frequency is correct for checking the foam concentrate pump operation?
• Cast iron shall not be used when?
• DOT containers cannot be recharged without test if five years have passed since last test. True or false?
• For foam solution piping, which material is listed as an option?
• Which extinguishing agent is specified by NFPA 12 for carbon dioxide systems?
• After an extinguisher is used, which statement best describes what should be documented as part of the post-incident process?
• A warning sign location is not listed in the standard locations if placed where?
• What PPE consideration is appropriate when using extinguishers in enclosed spaces?
• Foam sample shall be sent annually to whom for testing?
• The alarm in a clean agent fire suppression system should begin operating before what event?
• NFPA 25 provides standards for which aspect of water-based fire protection systems?
• Which statement describes the usage of galvanized and carbon steel for foam concentrate piping?
• Which of the following is NOT a transport consideration?
• Which material is explicitly allowed for foam solution fittings by AHJ/manufacturer?
• Which standard addresses Halon 1301 Fire Extinguishing Systems?
• Which labeling detail confirms suitability for electrical fires?
• Which statement describes the piping allowed on clean agent systems?
• If a fire is larger than what one extinguisher can handle, which action should be taken?
• The acronym ANSI stands for what organization?
• How do inspection and maintenance differ for fire extinguishers?
• High pressure system hoses shall be tested at what PSI?
• If you cannot identify the fire class due to an unclear label, what should you do?
• Why are regular drills and hands-on practice important for extinguisher readiness?
• Which of the following is a recommended action for maintaining extinguisher readiness in terms of storage location?
• Which of the following accurately reflects the policy on mechanical grooved couplings?
• How should extinguishers be labeled for kitchen areas to communicate their intended use?
• If you encounter a smoky area with no visible flame, what is the proper response?
• Which pipe material is NOT allowed on clean agent systems?
• Describe the PASS technique and its purpose?
• Which of the following statements about foam concentrate piping shall not be galvanized or carbon steel?
• What is the difference between passive and active fire protection in extinguisher readiness?
• What is the maximum temperature to dry hoses after the test?
• How often shall you inspect enclosure of all other systems besides halon 1031?
• After an extinguisher is used in an incident, what is a recommended post-event action regarding training?
• Galvanized and carbon steel pipes are permitted on which part of a foam system?
• Which situation most clearly indicates you should evacuate rather than attempt to fight a fire?
• Why essential to select the correct extinguisher for the fire class?
• If foam test deviates more than 10%, what action should be taken?
• How often shall halon 1301 cylinders be weighed?
• Which statement is true about CO2 container storage?
• The standard ANSI Z535 governs which aspect of workplace safety?
• How often shall you inspect halon 1301 systems ?
• Dry chemical extinguishers are commonly used for A, B, and C; Class D (metal fires) typically requires a specialized metal-fire agent.
• Class K extinguishers are designed for which type of fire?
• Which NFPA standard addresses the use and testing of high-expansion foam?
• How often to check pressure/quantity if clean agent system?
• What considerations apply when transporting extinguishers between locations?
• What determines whether an extinguisher is appropriate for a specific fire class?
• Under what conditions is it appropriate to use a water-based extinguisher?
• Is it acceptable to discharge halon 1301 into atmosphere?
• If you find an extinguisher with a damaged seal, missing pin, or deformation, what should you do?
• Which statement best describes the accepted practice for foam concentrate piping materials?
• The pre-discharge alarm in a clean agent system is intended to achieve which outcome?
• What are the three elements of the fire triangle that must be removed or controlled to stop a fire?
• Which safety risk can arise during extinguisher maintenance or inspection?
• What does the A rating indicate on an extinguisher?
• How often shall gauges be tested or replaced?
• Why might an extinguisher display combined ABC ratings?
• How often should personnel receive formal FEL-A procedures training?
• What is the purpose of the pressure gauge on a portable extinguisher and how should it be read?
• What should you do immediately after using an extinguisher on a small fire?
• Which statement is true about halon 1301 enclosure and related procedures?
• Inspection/maintenance for NFPA 15 shall refer to which NFPA standard?
• Foam concentrate piping galvanized material policy?
• What items should you verify during a monthly visual inspection of a portable extinguisher?
• The weight/pressure tag on halon 1301 containers should be updated at what interval?
• How often should low-pressure liquid level be checked?
• During halon 1301 visual inspection, what should not be stamped on the pressurized cylinder?
• If the extinguisher cannot reasonably control the fire, what should you do?
• Is galvanized pipe allowed for foam concentrate piping?
• When gauges are tested, they must read within what percent of a calibrated gauge?
• Why should extinguishers be kept away from direct sunlight and heat sources?
• Which statement describes common portable extinguisher media and the primary fire classes they address?
• Which of the following statements describes the material requirement for foam concentrate piping?
• The pre-discharge warning and alarm delay serves what purpose?
• DOT hydro testing interval: last test more than how many years ago?
• What should be done if the hose passes the pressure test?
• Does a clean agent system provide a pre-discharge warning and alarm delay to allow evacuation?
• Why is water not suitable for electrical fires?
• To whom should a report containing the recommendation be filed?
• NFPA 12 is the standard for which type of extinguishing systems?
• Which statement about Class K extinguishers is accurate?
• 3%AFFF means?
• Underground pipe shall be spot checked every how many years?
• What is a likely consequence of using the wrong extinguisher for a fire class?
• How does placement of extinguishers affect response time and safety?
• Full discharge test shall be performed:
• Which NFPA standard has the title Water Spray Fixed Systems for Fire Protection?
• Clean agent systems shall not be used on which hazards?
• How often are ALL systems hoses to be tested?
• Which NFPA standard covers Water Spray Fixed Systems for Fire Protection?
• How far should you stand from a fire when using a portable extinguisher, and what should you rely on to determine this distance?
• Foam solution fittings shall be which of the following materials?
• Mechanical grooved couplings and fittings are allowed on which type of system?
• What pipe is permitted on clean agent system?
• Can carbon steel pipe be used on foam systems?
• How should multiple extinguishers be used safely in a single incident?
• Which statement about foam solution piping is true?
• Low pressure supply pipe shall be a minimum of?
• How often shall low liquid level be checked?
• What is the purpose of keeping the tamper seal intact on a portable extinguisher?
• Which storage practice is NOT recommended for extinguishers?
• How often shall CO2 containers be weighed?
• Why is recharging after discharge necessary?
• The C rating on an extinguisher indicates suitability for which type of fire?
• Clean agent systems shall not be used on which hazards?
• How often shall Halon 1301 system be inspected?
• Inert gas must discharge 95% within how many seconds for class A-C fires?
• Which media is suitable for Class B and C fires?
• How can you determine whether an extinguisher’s agent is appropriate for electrical fires?
• Full discharge test requirement applies to which of the following?
• Which NFPA standard covers Low-, Medium-, and High-Expansion Foam?
• Which NFPA standard covers wetting agents?
• A fire safety plan should provide which information about extinguishers?
• How should extinguishers be stored in a workplace?
• What is the allowed material status for foam concentrate piping?
• DOT/CTC containers shall not be refilled unless they have been hydro tested within 5 years.
• Unlined fabric hoses shall NOT be used on foam systems.
• Halon 1301 system inspections are performed how often?
• If an extinguisher is not clearly labeled for the specific fire class, what should you do?
• Can flush bushings be used?
• Which material is listed as an option for foam concentrate piping?
• Total flooding system is defined as which of the following?
• Which standard would you consult for Clean Agent Fire Extinguishing Systems?
• Which system is explicitly associated with the use of mechanical grooved couplings?